iCarsoft i930 koodinlukija
Lähetetty: Ti Maalis 01, 2016 7:21 pm
Tervehdys !
Aion itse hankkia itselleni ICarsoft i930 Landrover/Jaguar vikakoodinlukijan. Lukijalla pääsee käsikksi (Jaguarforums.com) keskustelujen ja tuotetietojen mukaan kaikkiin Jaguar moduleihin. Hinta halvimmillaan noin 150€ posteineen(edit 2.3.2016) http://www.ebay.com/itm/Jaguar-iCarsoft ... SwNSxVXje2
Tuotetietoja:
Jaguar 1996-2015
- 1996 - 2014 XJ TYPE
- 2008 - 2014 XF TYPE
- 1997 - 2015 XK TYPE
- 2014 - 2014 F TYPE
- 1999 - 2008 S TYPE
- 2001 - 2009 X TYPE
Supported systems include:
Engine, PCM, TCM/Gear box, ABS, RCM/ SRS/ Airbag, ICCM/IP, RLCM /Air Suspension, BCM/BODY, HVAC/Air Conditioning, VDCM, SASM/Steering, TPM, PBM, Parking assist, Parking Aid, AHCM, VICM/Security/Immo, DDM, DSM, PDM, PSM, ATCM, TCCM/Transfer Box, ADCM, SCM, DRM, Rain Sensor, GSM, Light check/Lighting, OCS, HCM, ICM, KVM, Television
OBD-II Functions:
1. Read Codes
2. Erase Codes
3. I/M Readiness -- I/M Readiness indicates whether or not the various emissions-related systems on the vehicle are operating properly and are ready for Inspection and Maintenance testing.
4. Data Stream
5. Freeze Frame -- When an emission-related fault occurs, certain vehicle conditions are recorded by the on-board computer. This information is referred to as freeze frame data. Freeze Data is a snapshot of the operating conditions at the time of an emission-related fault.
6. O2 Sensor Test -- This option allows retrieval and viewing of O2 sensor test results for most recently performed tests from the vehicle’s on-board computer.
7. On-Board Monitoring -- This function can be utilized to read the results of on-board diagnostic monitoring tests for specific components/systems.
8. Evap System Test -- The EVAP test function lets you initiate a leak test for the vehicle’s EVAP system. Before using the system test function, refer to the vehicle’s service repair manual to determine the procedures necessary to stop the test.
9. Vehicle Information -- The option displays the vehicle identification number (VIN), the calibration verification number (CVN), and other information of the test vehicle.
10.Retrieve generic (P0, P2, P3, and U0), manufacturer specific (P1, P3, and U1) codes and pending codes
11.Turn off Check Engine Light (MIL), clear codes and reset monitors
12. Read live PCM datastream
13. Support CAN (Controller Area Network) and all other
14.Multilingual menu and DTC definitions- English, Spanish, and German, etc
15.Read pending DTCs
16.Read permanent DTCs
17. DTCs search
18. Supports all the OBDII/EOBD test modes include: CAN, ISO9141, KWP2000, J1850 VPW and J1850 PWM.
19. Works on all 2001 and later OBDII compliant PETROL European vehicles
20. Works on all 2004 and later OBDII compliant DIESEL European vehicles
21. Works on all 1996 and later OBDII compliant US and Asian vehicles
22. View & Graph Live Data in Color Graphing and blazing fast refresh rate for better graphing and live data readings.
23. Comprehensive Help, Including OBD Parameter, Mode Explanations & More
Specifications:
Display: 2.8” Color screen, 320 x 240 pixel display with contrast adjustment
Power: 8V -- 24V
Multi-Language: English, German
Updateable Online - First year of updates is free
Jaguarforums.com keskusteluissa http://www.jaguarforums.com/forum/s-typ ... er-156948/selvisi käytännön ongelmakin muuten melko mainiossa ja halvassa laitteessa jolla pääsee kaikkiin moduleihin toisin kuin monet geneeriset koodinlukijat eli se tärkein jää ns NoObd2 moodilla lukematta eli ECM(engine control module)/PCM koodit eli P koodit. Jos koneeseen lataa Obd2 moodin se tietty lukee nuo P koodit, mutta sitten pääsy joihinkin moduleihin estyy.
Kysyin tätä asiaa laitetta myyvän Elekma.com asiakaspalvelusta ja vastaus oli " laitteen muisti ei mahdollista kummankin ohjelmoinnin päällekkäisyyttä, mutta sivustolta http://www.icarsoft.com/web/icarsoftus/ ... ga3_1.html saa ladattua ilmaiseksi nuo ohjelmat.
Mutta kuten Jaguarforums.com linkissä todettiin, aion myös itse tehdä siten, että käytän icarsoft laitetta NoObd2 moodissa jotta saa nuo Jaguarkoodit ulos muista moduleista ja käytän jo nyt hommattua geneeristä laitetta mahdollisten P koodien lukuun. Kuulostaa ehkä hankalalta näin, mutta tuolla noin 150€ hinnalla ei oikein saa kuin kerran/kaksi luettua vikakoodit Jaguar lukulaitteella ja jäljelle jää muutama euroa keppanaan sekä oikeasti tarjontaa näinkin kattavalle lukijalle ei juuri ole.
Pitää laittaa päivitystä kun tulee kokemusta laitteesta.
Jos jollain on kyseinen laite käytössä, niin kokemuksia olisi hyvä kuulla myös.
Edit
Laitetta myydään monasti pelkästään ICarsoft i930 Landrover nimellä, mutta sisältää myös Jaguar softan ns ylimääräisenä.
Aion itse hankkia itselleni ICarsoft i930 Landrover/Jaguar vikakoodinlukijan. Lukijalla pääsee käsikksi (Jaguarforums.com) keskustelujen ja tuotetietojen mukaan kaikkiin Jaguar moduleihin. Hinta halvimmillaan noin 150€ posteineen(edit 2.3.2016) http://www.ebay.com/itm/Jaguar-iCarsoft ... SwNSxVXje2
Tuotetietoja:
Jaguar 1996-2015
- 1996 - 2014 XJ TYPE
- 2008 - 2014 XF TYPE
- 1997 - 2015 XK TYPE
- 2014 - 2014 F TYPE
- 1999 - 2008 S TYPE
- 2001 - 2009 X TYPE
Supported systems include:
Engine, PCM, TCM/Gear box, ABS, RCM/ SRS/ Airbag, ICCM/IP, RLCM /Air Suspension, BCM/BODY, HVAC/Air Conditioning, VDCM, SASM/Steering, TPM, PBM, Parking assist, Parking Aid, AHCM, VICM/Security/Immo, DDM, DSM, PDM, PSM, ATCM, TCCM/Transfer Box, ADCM, SCM, DRM, Rain Sensor, GSM, Light check/Lighting, OCS, HCM, ICM, KVM, Television
OBD-II Functions:
1. Read Codes
2. Erase Codes
3. I/M Readiness -- I/M Readiness indicates whether or not the various emissions-related systems on the vehicle are operating properly and are ready for Inspection and Maintenance testing.
4. Data Stream
5. Freeze Frame -- When an emission-related fault occurs, certain vehicle conditions are recorded by the on-board computer. This information is referred to as freeze frame data. Freeze Data is a snapshot of the operating conditions at the time of an emission-related fault.
6. O2 Sensor Test -- This option allows retrieval and viewing of O2 sensor test results for most recently performed tests from the vehicle’s on-board computer.
7. On-Board Monitoring -- This function can be utilized to read the results of on-board diagnostic monitoring tests for specific components/systems.
8. Evap System Test -- The EVAP test function lets you initiate a leak test for the vehicle’s EVAP system. Before using the system test function, refer to the vehicle’s service repair manual to determine the procedures necessary to stop the test.
9. Vehicle Information -- The option displays the vehicle identification number (VIN), the calibration verification number (CVN), and other information of the test vehicle.
10.Retrieve generic (P0, P2, P3, and U0), manufacturer specific (P1, P3, and U1) codes and pending codes
11.Turn off Check Engine Light (MIL), clear codes and reset monitors
12. Read live PCM datastream
13. Support CAN (Controller Area Network) and all other
14.Multilingual menu and DTC definitions- English, Spanish, and German, etc
15.Read pending DTCs
16.Read permanent DTCs
17. DTCs search
18. Supports all the OBDII/EOBD test modes include: CAN, ISO9141, KWP2000, J1850 VPW and J1850 PWM.
19. Works on all 2001 and later OBDII compliant PETROL European vehicles
20. Works on all 2004 and later OBDII compliant DIESEL European vehicles
21. Works on all 1996 and later OBDII compliant US and Asian vehicles
22. View & Graph Live Data in Color Graphing and blazing fast refresh rate for better graphing and live data readings.
23. Comprehensive Help, Including OBD Parameter, Mode Explanations & More
Specifications:
Display: 2.8” Color screen, 320 x 240 pixel display with contrast adjustment
Power: 8V -- 24V
Multi-Language: English, German
Updateable Online - First year of updates is free
Jaguarforums.com keskusteluissa http://www.jaguarforums.com/forum/s-typ ... er-156948/selvisi käytännön ongelmakin muuten melko mainiossa ja halvassa laitteessa jolla pääsee kaikkiin moduleihin toisin kuin monet geneeriset koodinlukijat eli se tärkein jää ns NoObd2 moodilla lukematta eli ECM(engine control module)/PCM koodit eli P koodit. Jos koneeseen lataa Obd2 moodin se tietty lukee nuo P koodit, mutta sitten pääsy joihinkin moduleihin estyy.
Kysyin tätä asiaa laitetta myyvän Elekma.com asiakaspalvelusta ja vastaus oli " laitteen muisti ei mahdollista kummankin ohjelmoinnin päällekkäisyyttä, mutta sivustolta http://www.icarsoft.com/web/icarsoftus/ ... ga3_1.html saa ladattua ilmaiseksi nuo ohjelmat.
Mutta kuten Jaguarforums.com linkissä todettiin, aion myös itse tehdä siten, että käytän icarsoft laitetta NoObd2 moodissa jotta saa nuo Jaguarkoodit ulos muista moduleista ja käytän jo nyt hommattua geneeristä laitetta mahdollisten P koodien lukuun. Kuulostaa ehkä hankalalta näin, mutta tuolla noin 150€ hinnalla ei oikein saa kuin kerran/kaksi luettua vikakoodit Jaguar lukulaitteella ja jäljelle jää muutama euroa keppanaan sekä oikeasti tarjontaa näinkin kattavalle lukijalle ei juuri ole.
Pitää laittaa päivitystä kun tulee kokemusta laitteesta.
Jos jollain on kyseinen laite käytössä, niin kokemuksia olisi hyvä kuulla myös.
Edit
Laitetta myydään monasti pelkästään ICarsoft i930 Landrover nimellä, mutta sisältää myös Jaguar softan ns ylimääräisenä.